Mark Super SV

• Damper elements absorb shock and vibration
• Vibration-free machine operation
• Set screws allow for easy machine alignment

• With self-actuated slide advance and automatic stop activation
• Can be used on drill presses, lathes, milling machines, etc.
• Automatic advance ensures constant tool feed
• Adjustable guides
• Adjustable stops
• Made of carbon-chromium-molybdenum steel
• All parts are hardened and precision-ground
• Guaranteed maximum accuracy
• Incl. reducing sleeves 4, 8, 12 mm

• Reducing sleeves are used for tool mounting with Morse taper shanks on lathes, drill presses, and milling machines
• The sleeves are hardened to ensure a secure hold, and ground inside and outside

• Reducing sleeves are used for tool mounting with Morse taper shanks on lathes, drill presses, and milling machines
• The sleeves are hardened to ensure a secure hold, and ground inside and outside

• Reducing sleeves are used for tool mounting with Morse taper shanks on lathes, drill presses, and milling machines
• The sleeves are hardened to ensure a secure hold, and ground inside and outside

• For cutters with cross or longitudinal slot
• Including parallel key, driver ring, cutter tightening screw, special wrench
• Thread: M16

• For cutters with cross or longitudinal slot
• Including parallel key, driver ring, cutter tightening screw, special wrench
• Thread: M16

• Incl. keyless drill chuck and drill chuck arbors
• In wooden case

Content / Set:

• Reducing sleeve: MT 4 / MT 3
• Reducing sleeve: MT 4 / MT 2
• Reducing sleeve: MT 4 / MT 1
• Extension Sleeve: MT 4 / MT 5
• Tool holder bit: MT 4 / B 18
• Tool holder bit: MT 4 / B 16
• Keyless drill chuck: 3-16 mm / B 18
• Keyless drill chuck: 1-13 mm / B 16

• With inside and outside Morse taper shank
• With tangs
• Fully hardened and ground
• Maximum concentricity

• Hardened and precision-ground for maximum concentricity, MT shank and tangs
• Precise and cost-effective design for mounting of drill chucks on drill presses, lathes, equipment, etc.

• Hardened and precision-ground for maximum concentricity, MT shank and tangs
• Precise and cost-effective design for mounting of drill chucks on drill presses, lathes, equipment, etc.

• Chucking range 1-13 mm
• Mount B 16

• Chucking range 3-16 mm
• Mount B 18

• 52 parts
• In a convenient, sturdy steel magazine
• 24 stud bolts, 4 each in the lengths 75, 100, 125, 150, 175, 200 mm
• 4 extension nuts, 6 stepped clamps (3 pair), 6 T-slot nuts, 6 hexagon nuts flanged, step blocks (3 pairs)

• High quality steel, black-finished
• Available in pairs only

• Integrated quick-return acts promptly upon feed direction change
• Slip coupling torque adjustable to 4 levels
• Including MT 3 and MT 4 shank
• For thread cutter

• Integrated quick-return acts promptly upon feed direction change
• Slip coupling torque adjustable to 4 levels
• Including MT 3 and MT 4 shank
• For thread cutter

• 6 pcs: 6, 8, 10, 12, 16, 20 mm

• 6 pcs: 6, 8, 10, 12, 16, 20 mm

• For clamping tools with cylindrical shank in ER collets according to DIN 6499

• For clamping tools with cylindrical shank in ER collets according to DIN 6499

• 1-two-sided 10x10x4 / 2-single sided 10x10
• 3-two-sided 10x10x4 / 4-single sided 10x4
• 5-two-sided 12x12x4

• With cross groove
• Right-hand cut with right-hand spiral
• HSS-E, hardness HRC 68
• Roughing cut teeth

• With cross groove
• Right-hand cut with right-hand spiral
• HSS-E, hardness HRC 68
• Roughing cut teeth

• With cross groove
• Right-hand cut with right-hand spiral
• HSS-E, hardness HRC 68
• Roughing cut teeth

TiN-coated, 20 pieces

• 2 - 5 times longer service life
• Double cutting power
• Improved part surface

DIN 327 D, short length

• Designed with 2 cutting edges. Face teeth for centric cuts. For cutting keyways/grooves (P 9 fitting) and center cut-out. Vertical or side cutting possible, with cyl. shaft and side drive dog acc. to DIN 1835 B, 3, 4, 5, 6, 8, 10, 12, 14, 18, 20 mm

DIN 844 B, short length

• Designed with 4 cutting edges with 30° right-hand spiral for excellent chip removal. Facing teeth for centric cuts. For normal to hard materials with cyl. shaft and side drive dogs DIN 1835 B, 3, 4, 5, 6, 8, 10, 12, 14, 18, 20 mm

• For easy inside diameter turning on drill presses, lathes and milling machines
• Micrometer screw for precise inside turning diameter adjustment
• High quality steel hardened and precision-ground
• Feed: 0.01 mm / division line
• 2 vertical tool mounts, 1 horizontal tool mount

• For easy inside diameter turning on drill presses, lathes and milling machines
• Micrometer screw for precise inside turning diameter adjustment
• High quality steel hardened and precision-ground
• Feed: 0.01 mm / division line
• 2 vertical tool mounts, 1 horizontal tool mount

• Mount with connection thread for reaming heads
• With draw-in bolt thread for use on milling machines
• Tapers are hardened and ground
• The reaming head set is provided without mount
• Shank with draw-in thread MT 4

• Gear ratio 1:90, disengages for direct division, manual 360° rotation of chuck
• Hand wheel with scale ring
• Nonius division 10''
• 6 masks for direct division of 2, 3, 4, 6, 8, 12, 24 parts
• Hardened and ground teeth with 3-jaw chuck, 160 or 200 mm

The S 200 Direct Indexing Head can be used in a horizontal or vertical setup. The indexing unit is enclosed in the resistant cast-iron body of the divider, where it is protected from contamination to ensure precise and constant divisions of 2, 3, 4, 6, 8, 12, and 24. An easy-to-read circumferentially mounted Nonius scale provides exact divisions up to 360º. A sturdy clamping lever is provided for the torsion-proof fixture of the chuck at any set position.

The indexing unit is enclosed in the resistant cast-iron body of the divider, where it is protected from contamination to ensure precise and consistent divisions of 2, 3, 4, 6, 8, 12, and 24.

An easy-to-read circumferentially mounted Nonius scale provides exact divisions up to 360º.

A sturdy clamping lever is provided for the torsion-proof fixture of the chuck at any set position.

Applications: Workpieces can be clamped between the divider and the tailstock for a horizontal workpiece alignment.

Upgrade to a Universal Divider

Dividing plate set for indirect dividing:

• The spindle is positioned via dividing plates that have several concentric hole pattern
• Using so-called shears (two pointers rotating around the crank shaft) simplifies positioning through several crank rotations, since counting between holes on the divider plate is not necessary
• The user only has to count the number of full rotations
• Benefit: Many divisions can be performed with only a few divider plates, higher accuracy is achieved by using a reduction worm gear, which causes a high-resolution continued rotation of the crank

• Hardened and precision-ground jaws and body
• High precision and wear-resistant material ensure long service-life
• Clamping pressure is up to ten times as high as with conventional machine vises
• Swivel-base mounted vise body, 360° swivel
• Constant clamping pressure, unaffected by vibration and shock
• Hydraulic power booster

• For direct and indirect division
• From 2 to 66, all divisions from 68 to 132 dividable by 2, 3 a. 5 can be performed

• Completely enclosed design, prevents contamination from dirt and chips
• Setup table rotates on a large ring-shaped box way
• The very effective clamp pulls the setup table down straight, without any change of position or radial pressure and presses it against the guideway
• For quick manual turning, the worm can be disengaged from the worm gear by pushing down the hand-lever
• Setup table with 360° scale
• The zero-backlash of worm and worm gear is adjustable
• Hand wheel scale gradation 10''
• Hand wheel can be replaced with indexing plate

• With 4 radial setup T-slots (14 mm)
• Very low profile
• Guide slot in the vertical base plane

Accuracy (max. deviation):

• Sface concentricity of work table setup surface 300 : 0.015
• Concentricity of setup < = 0.015
• Parallelism of setup to base surface 300 : 0.02
• Concentricity of setup table taper bore < = 0.010
• Parallelism of bore axis to vertical setup surface 0.03
• Parallelism of bore axis to slot in the vertical setup surface 0.02
• Parallelism between vertical setup area and conus taper connection axis - tailstock center 0.02
• Parallelism between slot in the vertical setup surface and the connecting axis between centers 0.02
• Division accuracy 45"

• For setup on drill presses, milling machines, machining centers, etc.
• LED display lights upon workpiece contact
• Outside and inside centering
• When passing the reference edge, the calibrated ball is pushed off
• Shank 20 mm